KemSpec

DEODOR PRECLEAN - KemSpec

DEODOR PRECLEAN - KemSpec

CH-KOPG

Description

The anionic surfactants in Deodor Preclean rapidly reduce the surface tension of carpet fiber and hard surface floor coverings, tying up and suspending the oily soils released by the solvents allowing the fragrance to contact the source of the urine odor problem quickly and neutralize it. The solvents quickly emulsify all oily soils typically found in traffic lanes and suspends them for easy removal from the floor covering when the rinse step is added.

 

pdf_iconsmall.GIF Download Product Label

 

Dilution Directions:

For Use as a Heavy Duty Spot Remover (Including old urine)
Do not dilute For Use as a Spot and Odor Remover (Including urine)
Dilute Deodor preclean with 4 parts cold water (32 oz. Deodor preclean to 1 gallon cold water)

For Use as a Traffic Lane Cleaner and Encapsulation Cleaner
Dilute Deodor preclean with 10 parts water (12 oz. Deodor preclean to 1 gallon water)

For Use in restrooms
For restroom restoration; dilute Deodor preclean with 8 parts cold water (16 oz. to 1 gallon cold water)
For daily maintenance; dilute Deodor preclean with 16 parts cold water (8 oz. to 1 gallon cold water)

Directions for use on carpet:
Always test fabric for colorfastness before applying Deodor preclean or any other product. Apply a small amount of cleaner to a clean, white cloth and gently blot test area. If no color transfers to cloth or no change in original fabric occurs, continue with directions below.

Spot Removal
Blot and agitate the spotting solution. Allow 5 minutes dwell time then extract or rinse with water.

Heavily Soiled Traffic Lanes
Pre-spray area to be cleaned at a rate of 200 to 400 sq. ft. per gallon, agitate Deodor preclean thoroughly into the carpet’s pile, allow 10 minutes of dwell time then extract with an extractor using hot water and DFC 105 in the machine.

Interim Cleaning - Encapsulation Process
Pre-spray area to be cleaned at a rate of 1000 sq. ft. per gallon, agitate the pre-spray thoroughly into the carpet’s pile, allow Deodor preclean to dry before vacuuming. Use a commercial vacuum approved by the Carpet and Rug Institute.

Hot Water Extraction Process
Pre-spray area to be cleaned at a rate of 1000 sq. ft. per gallon, agitate Deodor preclean thoroughly into the carpet’s pile, allow 10 minutes of dwell time then extract with an extractor using hot water and DFC 105 in the machine. Hot water extraction should be used a minimum of every 4th encapsulation cleaning. (A longer dwell time will be beneficial when strong odors are present.)

Drying
Use air movers to speed dry the carpet. Make sure the carpet is dry before traffic is allowed on it to prevent rapid re-soiling.

Directions for use in restrooms:
Restoration: mop tile and grout liberally especially around urinals and toilets, allow 10 minutes dwell time then scrub the floor paying particular attention to the areas under and around the urinals and toilets, rinse the floor using a clean damp mop and fresh cold water. Allow the floor to dry before putting the restroom back into service. (More dwell time will be beneficial when strong odors are present, using hot water will intensify the odor problem.)

Daily maintenance: mop tile and grout liberally especially around urinals and toilets, allow 10 minutes dwell time then using a clean damp mop and fresh cold water rinse the floor. Allow the floor to dry before putting the restroom back into service.

PDF File IconDE-ODOR PRECLEAN SDS [64 KB - pdf]

 
© Cleaning Systems Limited
www.cleaningsystems.co.nz